Our New Articles
T1 Lines, How To Test T1 Lines
by Jimmy Sturo
Many T1 lines are installed without proper testing and configuration. It is important for the provider and the customer to balance risks arising out of this situation, not only to avoid expenses on testing equipment, but also to make the T1 line error free. T1 line testing is a slightly complicated process for a technical amateur. You need to know the technical aspects of Internet thoroughly to connect the T1 lines and get it working properly. But there are a few simple procedures that could be followed to test the working condition of aT1 line, or to find out what has gone wrong during a breakdown.
During a break down, the first step is to determine whether the problem is with your PC or the T1 line. If you get a message saying the computer is using a saved version of your default home page when you open your Internet explorer, there is definitely something wrong with the T1 line. The next step is to check if the CSU/DSU, the router and hub are plugged into the telephone line and their lights are blinking. If they are, switch them on and off alternately three or four times. This will solve most kinds of T1 line problems. Once you identify the problem, the best way and the most popular one to test signal problems on T1 cables is the Bit Error Rate (BER) test. After configuring each T1 line for the test, you should let it run from one minute to 240 hours. This will give an error statistics base in the T1 line.
You can also use Cisco or other loopback testing devices to isolate the problem of the T1 serial link. These can be software loopbacks or hardware plug-in loopbacks. Another way of running a BER test is to configure a remote testing tool which will transfer data simultaneously with the test pattern. Once the problem is identified using loopbacks in two different directions, they can be rectified by resetting multiplexers at either ends of the T1 line.
T1 Lines provides detailed information on T1 Lines, T1 Line Prices, How To Test T1 Lines, Cheap T1 Lines and more. For more information go to http://www.e-T1Lines.com and/or visit its affiliated site at http://www.i-T3.com for related information.
These articles on lifestyle and more
Return to the selection of t1 lines
You may want to try these articles on t1 lines
T1 Lines, Cheap T1 Lines by Jimmy Sturo Approximately 358 Words
T1 Lines, T1 Lines by Jimmy Sturo Approximately 372 Words
T1 Lines, T1 Line Prices by Jimmy Sturo Approximately 353 Words
You may want to try these websites for additional information
http://shopfort1.com/index.cfm?cogidsmh1cogni
http://shopfort1.com/
http://shopfort1.com/index.cfm?telidt1links
The information provided in this article is the express opinion of the author. Exchangenet is not responsible for the content!
Many T1 lines are installed without proper testing and configuration. It is important for the provider and the customer to balance risks arising out of this situation, not only to avoid expenses on testing equipment, but also to make the T1 line error free. T1 line testing is a slightly complicated process for a technical amateur. You need to know the technical aspects of Internet thoroughly to connect the T1 lines and get it working properly. But there are a few simple procedures that could be followed to test the working condition of aT1 line, or to find out what has gone wrong during a breakdown.
During a break down, the first step is to determine whether the problem is with your PC or the T1 line. If you get a message saying the computer is using a saved version of your default home page when you open your Internet explorer, there is definitely something wrong with the T1 line. The next step is to check if the CSU/DSU, the router and hub are plugged into the telephone line and their lights are blinking. If they are, switch them on and off alternately three or four times. This will solve most kinds of T1 line problems. Once you identify the problem, the best way and the most popular one to test signal problems on T1 cables is the Bit Error Rate (BER) test. After configuring each T1 line for the test, you should let it run from one minute to 240 hours. This will give an error statistics base in the T1 line.
You can also use Cisco or other loopback testing devices to isolate the problem of the T1 serial link. These can be software loopbacks or hardware plug-in loopbacks. Another way of running a BER test is to configure a remote testing tool which will transfer data simultaneously with the test pattern. Once the problem is identified using loopbacks in two different directions, they can be rectified by resetting multiplexers at either ends of the T1 line.
T1 Lines provides detailed information on T1 Lines, T1 Line Prices, How To Test T1 Lines, Cheap T1 Lines and more. For more information go to http://www.e-T1Lines.com and/or visit its affiliated site at http://www.i-T3.com for related information.
These articles on lifestyle and more
This article is available for syndication. It must be republished with its title, text, and hyperlinks in tact (HYPERLINKS MUST BE KEPT ACTIVE). t1 lines
Return to the selection of t1 lines
You may want to try these articles on t1 lines
T1 Lines, Cheap T1 Lines by Jimmy Sturo Approximately 358 Words
T1 Lines, T1 Lines by Jimmy Sturo Approximately 372 Words
T1 Lines, T1 Line Prices by Jimmy Sturo Approximately 353 Words
You may want to try these websites for additional information
http://shopfort1.com/index.cfm?cogidsmh1cogni
http://shopfort1.com/
http://shopfort1.com/index.cfm?telidt1links
The information provided in this article is the express opinion of the author. Exchangenet is not responsible for the content!
